ZZ4350 Engine and 4L60E Transmission Package
Get everything you need in one very economical engine and trans package. ZZ4 engine comes fully assembled. All you need to do is transfer over your belt driven accessories over and you're ready to run!
Imagine an aluminum head small block that makes 355 horsepower. What if it had a street roller camshaft, 4-bolt main block, 1053 forged steel crankshaft, high silicon pistons and strong PM connecting rods ? We imagined it, and then engineered, developed, tested and built it. The ZZ4 is the evolution of our popular ZZ series of small blocks that power thousands of street rods, hot street cars, circle track racers and drag racers.
With over 400 Ft-Lbs of torque, the ZZ4 is the best way to put an aluminum head, roller cam, high performance small block between your favorite fenders.
The aluminum angle plug cylinder heads have screw in rocker studs, 1.94" intake and 1.50" exhaust valves and 58cc combustion chambers that yield a crisp and responsive 10 to 1 compression ratio. Also included are our lightweight valve spring retainers that weigh half as much as our previous design. The valve seats are radiused and we have included valve stem seals to help keep the oil where it belongs. To compliment the cylinder head design, we've incorporated a steel roller tappet camshaft with .474" intake and .510" exhaust valve lift. The combination makes 355 horsepower at 5250 rpm and has that great sounding muscle car idle, with just enough lope to let people know this is no station wagon engine.
Also included with the ZZ4 is an HEI distributor with an ignition timing advance curve developed for performance, a dual plane aluminum intake manifold that accepts your spread bore or square bore carburetor, an 8" high-rpm harmonic balancer, 14" automatic trans flex plate and a cast iron water pump. It even has the spark plugs in it! The ZZ4 is currently our most popular crate engine, and you can see why. With a long history of successes in circle track and drag racing as well as street rods and other performance applications, the ZZ4 may just be the bullet for your next project. The ZZ4 is not intended for marine use, and should only be used in 1973 and earlier pre-emissions street vehicles or any year off road vehicle.
Power: 355 HP @ 5400 RPM, 405 ft. lbs. of torque @ 3600 RPM
Displacement: 350 CID, 5.7L
Bore x Stroke: 4.00” x 3.48”
Compression Ratio: 10:1
Recommended Fuel: 92 Octane
Block: Cast Iron, 1 piece rear seal, 4-bolt main caps.
Crankshaft: Forged Steel
Connecting Rods: Powdered Metal Steel
Pistons: High Silicone Aluminum
Camshaft: Steel Hydraulic Roller Tappet
Cam Lift: .474” Intake / .510” exhaust
Cam Duration @ .050”: 208 deg. Intake / 221 deg. Exhaust
Lobe Separation: 112 Degree
Cylinder Heads: Aluminum, 3/8” screw-in rocker studs.
Combustion Chamber: 58cc
Valves: .194” Intake/ 1.50” Exhaust
Rocker Arms: Stamped Steel, 1.5:1 Ratio
Valve Springs: 12551483
Carb: GM Tuned Holley 770CFM Vacuum Secondaries
Maximum GM Recommended RPM: 5800
Ignition Timing: Base 10 degrees BTDC, 32 degrees total
• Fully GM assembled long block
• Steel OE Center Bolt Valve Covers
• Steel Chrome 14” Air Cleaner with Chevy Logo
• Oil pump, pick-up and oil pan
• Aluminum Performance Intake
• GM Tuned 770CFM Holley Carb
• Performance Fuel Pump with Plumbing to Carb
• HEI Distributor, Plug Wires, Looms and Spark Plugs
• 14” Auto Trans Flexplate
• HD Starter with Bolts
• 8” Harmonic Balancer
• Front timing cover
• Cast Iron Long Water Pump
• Oil Filter and Adapter
• Passenger Side RH Oil Dipstick and Tube
4L60E Trans Package Includes:
• GM Performance 4L60E 4 Speed w/overdrive Automatic Transmission
• GM Performance 2300-2500 Stall Convertor
• Slip Yoke (front driveshaft yoke)
• HD Urethane Trans mount
• Locking Dipstick, Tube & Seal
• Transmission controller with harness
• Throttle Position Sensor with Bracket
• GM Performance 4L60E Installation Package
General Motors limited 2 year / 50,000 mile parts & labor warranty. Click on Document tab above for full details.